login   |    register
Dragon Models [ MORE REVIEWS ] [ WEB SITE ] [ NEW STORIES ]

In-Box Review
135
Pz.IV Ausf B w/ Schneeräumer
Pz. Kpfw. IV Ausf. B mit Schneeräumer Syste Schmidt 1/35 '39-'45 series
  • move

by: Russ Amott [ RUSSAMOTTO ]


Originally published on:
Armorama

introduction
The Panzer IV series was the workhorse tank of WWII Germany, remaining in production through several models from before the war began until it ended May 9, 1945. It saw action in large numbers on all fronts. The Ausf. B variant was a pre-war production model of 42 vehicles manufactured at Krupp between 1937 and 1938. It was powered by a 12 cylinder Maybach HL 120TR engine with 300hp, an upgrade from the engine that powered the Ausf. A. The glacis armor plate was thickened to 30mm and the hull mounted machine gun port was covered over. It mounted a short barreled 7.5cm L24 cannon that fired primarily low velocity, high explosive shells. It was intended to be a support tank for infantry that would destroy enemy fortifications while enemy armor would be handled by the Panzer III.

The German Army experimented with a number of tools and options for their tanks for dealing with a variety of obstacles including water, barriers, and in the case of this subject, snow. The Schneeräumer system Schmidt was a snow moving device. Roughly translated as "snow pusher", it was intended to push the snow to the sides, under the tracks of the tank. This would clear the snow and allow the tank to maintain traction. Whether it was used in combat on the Panzer IV B is not verified, but similar devices were widely used on other vehicles, including half tracks.

The Panzer IV ausf. B saw combat service in Poland, France and the Soviet Union before it was pulled from front line service. It remained in reserve and training units. I have read that two were involved in the fighting following the Normandy invasion.

the kit
Several years ago, Cyber-Hobby released the Pz. IV Ausf B as a limited edition kit. Dragon has now re-released the kit as part of their '39-'45 series. This is not a smart kit release, containing an extended number of parts and photo-etch. For those who missed out when the kit was released before, this is a new opportunity to get it.

In looking over previous reviews of the Panzer IV series from Dragon, including the previous review of the Panzer IV ausf. B from Cyber-Hobby that was done here by Vinnie Branigan, it is apparent that Dragon has taken the easy route and used the same sprues from previous releases, only adding parts that are needed for the earlier version. As such, many sprues in the previous ausf. D and ausf C releases are seen here again. The molds have probably been cleaned up and some details sharpened as all the sprues look clean and new. Half the alphabet is used identifying the sprue trees and roughly a third of the parts are marked not for use.

Sprue A, X2, from the previous ausf. D and C releases, has a working suspension with optional drive sprockets on which you can add the bolts on your own or use pre-molded bolt heads. The bogie mountings are for the later C and D variants and my understanding is that they should have a different bolt head (see Terry Ashley's review of the Tristar Pz. IV B at PMMS). One thing I really like here is that the tires on the road wheels are a separate part. This increases the parts count, but will make painting much easier. I wish this option was available on all tank road wheels.

Sprue B, also from the previous releases, has the final drive system with inner gears, and hull fitting. There are multiple options for the final drive housing, with the kit instructions indicating to use those without any bolt heads, and attach 6 separate bolt heads to the part. Again, Terry Ashley indicates that only three bolt heads were present on the ausf. B. His list of references is far more extensive than mine.

Sprue C, new for this kit, is the Schneeräumer system. The blade is thin and has nice bolt head detail. I have yet to see a photo of the actual vehicle so I can't comment on the accuracy, but it does look good.

Sprue D is from the ausf C and D kits. The muffler, fender parts, and tow brackets - plus some small detail items - are used here. The fenders are an optional part as these have placement holes for the optional tools with molded-on clasps.

Sprue E again is from the ausf C andD kits. Only the hull hatches, tow hooks, antenna guard and rear bolt strip are used.

Sprue F, from the ausf. C and D kits, is the turret basket and main gun assembly. The 7.5cm gun has a pre-bored, rifled muzzle.

Sprue H holds two sets of tools, one with molded on clamps, the other without. Also, three jerry cans, a jack, head lamp and tow cable ends.

Sprue J, again from the ausf. C and D release, uses the turret base, ventilation fans for the engine, and some engine deck fittings.

L parts are slide molded idler sprockets, an optional part but better detailed than the two halves you would otherwise assemble.

Sprue P has clear parts for vision blocks, sights and headlight.

Sprue Q has the Commander's cupola present in most every Pz. III and IV kits. The 25-part assembly is intricate, but not difficult, and looks very nice when complete.

Sprue R has small clear vision blocks.

Sprue S, from the ausf. c and d, has fenders with no holes, for mounting tools with etch clamps. All fenders have top and bottom detail and are very thin.

Part U is a slide-molded part for the cupola.

V parts are separate tires for the road wheels, embossed with "Continentau".

W sprue has the upper hull, rear hull and fittings. Optional styrene air intake louvers are on this sprue. This was in the ausf. C kit as well.

X part is the lower hull. Well detailed on sides and bottom, bump stops are present on the first and fourth bogie positions.

Y sprue, new to the ausf. B, is the revised inner mantlet, antenna guard and plate detail.

K and M parts are the left and right side tracks. They are handed and colored light and dark gray.

Ma, MB, MC, MD and ME are the photo-etch and metal accessories. MA is from the previous releases and has tool clamps and detail accessories, including the fold-down step on the side. MB is a set of etched engine air intake louvers and the metal insert for the jerry cans, as well as chains for the smoke launchers. MC provides four etched inserts for the idler wheels. ME has handles and cables, pre-formed, for the lights, and the cover for the shovel blade. MD is a turned aluminum barrel pre-bored, but without rifling, and two turned-brass rounds.

Z part is a twisted wire for the tow cable.

Detailing on the parts is very crisp and well defined. I found no deformities or molding issues.

Instructions
The instructions are line drawings with drop boxes showing sub assemblies. Sub assemblies are also indicated by letter. In step one, assembly of the rear light, part F is shown. This is not installed until the very last step, so keep this in mind. Total assembly is in 23 steps.

paint and markings
Paints are called out by color and number for GSI Creos aqueous hobby color and Mr. Color, as well as Testors Model Master paints.

Three specific vehicles are represented in the decals.

Vehicle 1 is from an unidentified unit, 1938, and shows the Schneeräumer system installed.

Vehicle 2 is from 8Kompanie/Pz.Rgt.1, 1st Panzer division, Poland 1939.

Vehicle 3 is from 4Kompanie/Pz.Rgt.1, 1st Panzer division, France, 1940.

All three vehicles are in overall Dark Gray.

conclusion
This is a very complete kit with lots of detail. The parts count will make it somewhat challenging for less experienced modelers, but it should be well worth it.

Online prices varied for this kit, ranging from $54.00 up to over $80.00, all before shipping. As always, look for the best offer.

A Build Log has been started in the forums.
SUMMARY
Highs: Excellent level of detail. The kit can be built as a standard Panzer IV ausf B or with the Schneeräumer system installed.
Lows: I would have liked a couple more decal options for the standard Pz. IV B. Possible accuracy issues with some small parts.
Verdict: I think this is an excellent kit. From reading online build logs it should assemble quite well.
Percentage Rating
90%
  Scale: 1:35
  Mfg. ID: 6764
  Suggested Retail: $54.95 US
  Related Link: DragonUSA Item Page
  PUBLISHED: Feb 10, 2013
  NATIONALITY: Germany
NETWORK-WIDE AVERAGE RATINGS
  THIS REVIEWER: 84.47%
  MAKER/PUBLISHER: 86.19%

Our Thanks to Dragon USA!
This item was provided by them for the purpose of having it reviewed on this KitMaker Network site. If you would like your kit, book, or product reviewed, please contact us.

View This Item   View Vendor Homepage  More Reviews  

Photos
Click image to enlarge
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
About Russ Amott (russamotto)
FROM: UTAH, UNITED STATES

I got back into the hobby a few years back, and wanted to find ways to improve, which is how I found this site. Since joining Armorama I have improved tremendously by learning from others here, and have actually finished a couple of kits. I model to relax and have fun, but always look to improve. ...

Copyright ©2017 text by Russ Amott [ RUSSAMOTTO ]. Images also by copyright holder unless otherwise noted. Opinions expressed are those of the author(s) and not necessarily those of TankRat's. All rights reserved.


Reader Reviews
Do you own this item and want to review it? You can add your review of the item here. Please read the reader review instructions before posting.


Comments

Personally, Id pick this up just for the ordinary Ausf.B. Missed it first time around. The blade doesn´t do anything for me, unless I wanted to do some sort of diorama around it. Thanks for the review Russ.
FEB 10, 2013 - 10:03 PM
Tom, thanks for helping with this and getting it posted. I forgot to mention that the tracks are the correct early 38cm. Hope I didn't miss anything else. Frank, thanks for the comment. I believe lots of modelers are thinking like you, and will grab this kit without wanting to use the blade. As such, I do wish they had included at least a couple more decal options.
FEB 10, 2013 - 10:33 PM
I wish there were fewer "unidentified unit" marking options across DML's kits. Hopefully the aftermarket fellas will help us out with some research and sets of markings for this one. I have the earlier Cyber Hobby release of the Ausf B about 70% completed, and the parts count is amazingly high.
FEB 11, 2013 - 06:22 PM
Tip: Just hit enter to submit your reply!
   
What's Your Opinion?


Photos
Click image to enlarge
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move